Products and Component Restoration

Home » Reproduction Parts & Specialty Coatings » All Products

 Checkout

Glass Setting Tape
Glass Setting Tape

Details 

The "right stuff" for installing wing glass into it's channel & other similar glass attachment such as door glass lower edge lift channel and quarter/door glass edge channels.

Includes detailed instructions for how to get a professional and correct original appearance!

Priced by the linear foot.

Price: $1.75
Add to cart

Headliner Bow Pocket Clips
Headliner Bow Pocket Clips

Details 

Set of 10 headliner bow pocket clips as used on 1969-70 B-body and 1970 E-body. These clips slide into rectangular cut outs on the roof sides. The headliner bow rests in the pocket of the clip.
Price: $35.00
Add to cart

Headliner Rear Bow Retainer Wires
Headliner Rear Bow Retainer Wires

Details 

Nice reproduction of the wires used to retain the rear headliner bow. Made from correct diameter spring tempered stainless steel. (Originals were zinc plated steel).

The arrow shaped end plugs into the rear roof crossmember and the other end hooks the rear bow. This keeps the bow in the correct position as the headlining material is pulled forward. Without these, the bows will "flop" over. The dome lamp location relative to the bows is also set by the rear bow position.

Available for various models, please inquire for your model's availability.

Price: $16.00
Add to cart

Heater Box Caulk
Heater Box Caulk

Details 

As used for sealing box halves to each other. Correct off-white color. Sold by the foot. Fits many applications. $.25/foot

NOTE: gasket kits include this material.

Price: $0.25
Add to cart

Heater Box Floor Duct Board
Heater Box Floor Duct Board

Details 

Heater box floor duct board for 70-4 E-body non-a/c cars. This part is an exact size reproduction made with original appearing black board material. It also has the correct pressed-in relief line where it bends as original.
Price: $14.00
Add to cart

Keystone Fuel Hose Clamps
Keystone Fuel Hose Clamps

Details 

Correct zinc plated color coded keystone type fuel hose clamps available in 1/4", 5/16 & 3/8" sizes. 1/4"= zinc dichromate, 5/16"= clear zinc, 3/8"= black zinc. *Note: The price shown will be automatically adjusted as necessary when you select your clamp size.
:
Price: $0.75
Add to cart

K-Member Oval I.D. Coin
K-Member Oval I.D. Coin

Details 

Correct thickness and shape. Available blank or specify number stamping desired. Please inquire for help with number, if needed.
Price: $20.00
Add to cart

Large Flange Rivet
Large Flange Rivet

Details 

Special steel large flange pop rivet as used on front frame rail splash shields and 69 Roadrunner & Superbee air grabber hood air induction ductwork.

Also available in aluminum as used on Superbird and Daytona nose areas.

:
Price: $0.50
Add to cart

Mirror Threaded Insert
Mirror Threaded Insert

Details 

10-24 threaded steel insert as used to fasten door mirror and rear window louvers.

Requires use of a threaded insert installation tool. A low-buck alternative is to use a 10-24 hex headed screw with a flat washer and a hex nut. The screw is threaded into the insert with the hex nut threaded on the screw. While holding the screw to prevent it from turning, the hex nut is tightened to compress the threaded insert. The insert must be held tightly to the sheetmetal as the nut is tightened.

Price: $1.00
Add to cart

Power Steering Hose Clamp
Power Steering Hose Clamp

Details 

Power steering hose clamp for low pressure side. Correct red phosphate coating. Fits many applications.
Price: $0.75
Add to cart

Push Retainer
Push Retainer

Details 

Push retainer as used on A-body hood hinges (4 required) and E-body trunk hinges (2 required).

Price is each.

Price: $1.00
Add to cart

Quarter Window Roller B-body
Previous1 of 3Next
Quarter Window Roller B-body

Details 

Quarter window lift mechanism roller for B-bodies. 1.125" OD.
Price: $5.00
Add to cart

Quasimoline Paint
Quasimoline Paint

Details 

Urethane paint formulated to closely mimic the original cosmoline finish used on Mopar lower control arms. This is an ideal product for those wanting a durable finish that can be wiped clean and not hold dirt like the real thing. Dries to a satin gloss. Darkness & coloring will vary with number of coats applied and color of control arm. Thin with a urethane reducer, no hardener required. Sold in a half pint can for use with a spray gun. One can will easily do two sets of control arms, depending on application thickness. Can also be used to accentuate the coloring of some cast iron parts.
Price: $24.00
Add to cart

Rallye Mirror Screw
Rallye Mirror Screw

Details 

Oval head phillips screw with the correct head shape and diameter as used for Rallye mirror installation.

Correct chrome plated finish. (Not polished stainless steel like other incorrect reproductions!)

Price: $1.00
Add to cart

Rear End Axle Gaskets
Rear End Axle Gaskets

Details 

Correct white poly material gaskets for the rear end axle bearing flange to backing plate. These gaskets will fit both 8 3/4" & Dana 60 rear ends.

Price is for one pair of gaskets.

Price: $3.00
Add to cart

« Previous | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Next »

 


| home | about | restorations | shop tour | online store |
| tech board | rick's rides | testimonials | faq | news | resto links | contact |